Window&Door

Całoroczna, niskorozprężna poliuretanowa pianka montażowa PU do mocowania i uszczelniania okien i drzwi
oraz do mocowań i wypełnień budowlanych.

• Do stosowania w temperaturach od -10°C do +35°C
• Idealna do izolacji termicznej i akustycznej
• Wodoodporna
• Wydajność do 45 litrów z puszki 750ml.

WINDOW & DOOR dzięki stabilności wymiarowej i właściwościom mechanicznym związanej pianki idealnie nadaje się do klejenia, mocowania, izolowania, wygłuszania, uszczelniania i zaślepiania. Zastosowana w składzie materiału specjalna mieszanka propelentów powoduje, że może być on stosowany nawet w temperaturach otoczenia do -10°C. Ponadto struktura jednolitych komórek, głównie zamkniętych, nadaje utwardzonej piance właściwości termoizolacyjne i dźwiękoszczelne (patrz raporty z badań Istituto Masini 1016-2008 z 31.03.2008 i IFT 16732059 z 22.09.2006), zgodnie z IEC 64-8, art. 511.1. Pianka doskonale wiąże do drewna, betonu, cegły, azbestocementu, metalu, szkła i plastiku z wyjątkiem polietylenu, teflonu i silikonu. Utwardzona pianka może być cięta, wiercona, szlifowana, malowana, tynkowana. Produkt posiada certyfikat EC 1 Plus wydany przez GEV w zakresie bardzo niskiej emisji lotnych substancji organicznych.

Wykonanie prac

1. Surfaces must be free of oil, grease and dust. Dampen the surface before application to guarantee necessary humidity for the fresh foam to form even cell structure.
2. Remove the protection cap. Insert the can to application gun (T2000 or T500 from Torggler S.r.l.) or in case of manual version insert the extension nozzle on the dispenser. Screw the dispenser with the extension nozzle to the canister valve.
3. Shake the canister for at least 15 seconds before use. Repeat after each working break.
4. Turn the aerosol upside-down so that the valve is facing down, point the extension tube as required and press the dispenser with your fingers. The amount of foam required to fill the cavity depends on the subsequent expansion of the foam. In the case of low ambient humidity, moisten the kerbs immediately after extrusion.
5. The foam hardens completely in just approximately one hour after laying. After this time any excess material can be cut or sanded away.
6. If the canister is not completely emptied, return it to an upright position and press the nozzle for a few seconds. The gas which escapes will clean the valve and spray gun.

Cleaning
Traces of uncured foam on clothing, doors, window frames, etc. can be removed with specific
solvent. Hardened foam can only be removed mechanically (e.g. by scraping or sanding).

Observations
The yield of the foam depends greatly on the temperature, the canister and the substrate. At low temperatures both the output pressure of fresh material from the valve and the amount of hardened foam are reduced. To obtain a good yield, it is recommended that the canister be at a temperature of approx. 20°C. At higher temperatures it can be difficult to dose the product correctly, as the increase in pressure inside the cylinder makes it less easy to control the escape of material from the valve.

Przechowywanie

Keep in a cool place in an upright position. Avoid storing the canister in a horizontal position, as incrustations rapidly form under the valve which will irreparably compromise the extrusion of the foam. Window & Door has a shelf life of at least 18 months if stored upright in a cool (at a temperature below 25°C) and dry place.

Uwagi

Completely water-saturated substrates and structures prevent the foam from adhering.

The Window & Door can is a pressurized container. Protect from sunlight and do not expose it to temperatures above 50 °C. Do not puncture or burn, even after use. Do not spray over an open flame or on an incandescent element. Keep away from all sources of combustion. No smoking. Keep out of the reach of children. This product contains flammable components, so only use it in well-ventilated areas. There is the risk that explosive vapour/air mixtures may form, especially if more than one canister is used in the same location. Contains diphenylmethane-4,4’-diisocyanate (EEC no. 615-005-00-9). Extremely flammable. Harmful by inhalation. Irritating to eyes, respiratory system and skin. In case of contact with eyes, rinse immediately with plenty of water and seek medical advice. After contact with skin, wash immediately with plenty of soap and water. Wear suitable protective clothing and gloves. In case of insufficient ventilation wear suitable respiratory equipment. In case of accident or if you feel unwell seek medical advice immediately (show the canister where possible).