Rocksolid Lime M15

Fibre-reinforced concrete mortar, for the repair and structural reinforcement of plaster (including reinforced plaster) and breathable masonry, based on natural hydraulic lime (NHL).

Fibre-reinforced concrete mortar, for the repair and structural reinforcement of plaster (including reinforced plaster) and breathable masonry, based on natural hydraulic lime (NHL).

  • High mechanical strength
  • Based on natural hydraulic lime (NHL 5)
  • Suitable for ‘reinforced’ plasters (CRM)
  • Can be applied by hand or by machine
  • High breathability
  • For all types of masonry

Application areas

Choose Rocksolid Lime M15 for

  • Consolidation works on deteriorated or weakened masonry, used both as a consolidating roughcast to level out uneven surfaces and as a thick-set render with high mechanical performance, reinforced where necessary with metal or composite mesh to produce CRM (Composite Reinforced Mortar).
  • Installation of new high-performance, breathable plasters in line with the principles of environmental sustainability and green building, for both internal and external applications.
  • Construction of ‘reinforced coatings’ using metal or composite reinforcement mesh on the upper surface of vaults.

Discover more

Other solutions you might be interested in

Details

Instructions for use

The substrate must be clean, sound and sufficiently rough. Remove, either by hand or using mechanical tools, all loose or non-adhering parts, any existing plaster, dust, mould and any other material that could compromise the product’s adhesion. Carry out pressure washing to remove salt efflorescence, traces of oil, grease or other contaminants.
The joints between the bricks must be properly filled. Any cavities, gaps or cracks in the masonry must be filled at least two days before application by repointing or ‘un-seam-and-seam’ repairs, using the same Rocksolid Lime M15 mortar in combination with stone, brick or tuff elements that are as compatible as possible with the original materials.
Before application, dampen the substrate evenly to prevent it from absorbing too much of the mixing water, which could compromise the mortar’s performance. Remove any excess water before applying the product.
In the case of plaster or reinforced render, apply the metal or composite mesh after applying the first layer of plaster, securing it firmly to the existing masonry. The connectors must be compatible with the type of mesh used. For fibreglass mesh, compatible ‘L’-shaped connectors are recommended, at a rate of approximately 4–5 pieces per square metre, to be chemically fixed using Xtreme Grip Vinylester, a two-component vinyl ester resin-based anchor.
The two layers of plaster intended to embed the mesh must be applied wet-on-wet, taking care to maintain the roughness of the previous layer.

Product preparation
Rocksolid Lime M15 must be prepared according to the chosen application method:

  • Machine application: use a continuous-mix plastering machine fitted with a hopper, following the manufacturer’s instructions for setting the mixing and pumping parameters.
  • Manual application: mix the product in a bowl-type concrete mixer, gradually adding clean water until a homogeneous, lump-free consistency is achieved.
  • Small quantities: these can be mixed using a low-speed electric drill fitted with a whisk attachment to ensure even distribution of the binders and aggregates.

Use only the quantity of water specified in the technical data sheet. Avoid adding further water once mixing has begun, so as not to compromise the product’s performance.

Machine application
Mix Rocksolid Lime M15 in a continuous-mix plastering machine, adjusting the water flow to approximately 320–340 l/h, until a homogeneous consistency is achieved. Use pumps suitable for the type of aggregate. Apply the product in layers approximately 40 mm thick, working from the bottom upwards. For greater thicknesses, apply in several coats, leaving the previous coat unfinished. After a few minutes, level and finish the surface with a trowel (plastic, wooden or sponge), depending on the desired effect. Avoid applying to surfaces that are too hot or exposed to the wind. In the event of high temperatures or low humidity, protect the surface or mist it with water for the first 24–36 hours.

Manual application
Mix Rocksolid M 15 Lime with approximately 16 per cent clean water (equivalent to 4 litres of water per 25 kg bag) in a bowl-type concrete mixer, using a mechanical agitator (low-speed drill with a suitable mixing paddle) until the mixture is homogeneous and free of lumps. Apply with a trowel in layers no thicker than 40 mm per coat. For repointing or patching, spread the mortar at the base and insert the masonry units with light pressure. For exposed joints, apply a layer at least 2 cm thick and clean with water and a sponge float before setting.

Finishing
Before applying skim coats or finishes, allow the plaster to cure completely: approximately 7 days per centimetre of thickness. Use paints or coatings that do not significantly alter the breathability of the plaster, such as Finish Siloxan, a smooth siloxane-based paint. If no decorative finish is planned, in the case of surfaces exposed to the elements, the plaster can be protected with Promural Silicon, a transparent, vapour-permeable, water-repellent impregnating agent, ready for use, based on siloxane polymers dissolved in a solvent.

Cleaning
Tools used for application can be cleaned with water before the mortar sets; thereafter, cleaning can only be carried out by mechanical removal.

Storage

Store in a dry, sheltered place. It will keep for at least 12 months in its original, unopened bags.

Warnings

  • Do not mix Rocksolid Lime M15 with other products, so as not to alter its specific properties.
  • Avoid sudden changes in temperature whilst the plaster is setting.
  • Protect the plaster from frost for at least 3 days after application.
  • In the event of high temperatures, wet the substrate thoroughly before application and moisten Rocksolid Lime M15.
  • Do not use coloured paints or coatings that could significantly alter the breathability of the plaster made with Rocksolid Lime M15.
  • Apply at temperatures between +6 °C and +35 °C.

Code Packaging Packaging size Pallet Barcode
8395 * bag 25kg
50 bags
Barcode 8030334083952
*At request

  • Consolidation works on deteriorated or weakened masonry, used both as a consolidating roughcast to level out uneven surfaces and as a thick-set render with high mechanical performance, reinforced where necessary with metal or composite mesh to produce CRM (Composite Reinforced Mortar).
  • Installation of new high-performance, breathable plasters in line with the principles of environmental sustainability and green building, for both internal and external applications.
  • Construction of ‘reinforced coatings’ using metal or composite reinforcement mesh on the upper surface of vaults.

Texture powder
Colour light hazelnut
Mixing ratio Approx. 16 litres of water per 100 kg of product
Specific gravity of dry product Approx. 1650 kg/m³
Particle size 0–3 mm
Compressive strength at 28 days >15 MPa
Minimum application thickness 1.5 cm per coat
Reaction to fire Euroclass A1
Adhesion to the substrate 1.0 N/mm² FP:B
Water vapour permeability µ ≤ 15
Category GP – CSIV – W0 (EN 998-1) – M15 (EN 998-2)
Water absorption W0
Thermal conductivity (λ) tabulated value 1.11 W/mK
Operating temperature +6°C / +35°C
Packaging 25 kg bags – 1,250 kg pallets

 

16 kg/m² for every centimetre of thickness

Technical datasheet

Still missing information?

Contact our team for personalized support and product guidance.