Screed

A medium-drying, premixed cementitious mortar, class CT C20 F5 in accordance with EN 13813, for the installation of bonded or floating screeds.

A medium-drying, premixed cementitious mortar, class CT C20 F5 in accordance with EN 13813, for the installation of bonded or floating screeds.

  • Suitable for use in underfloor heating systems
  • Can be applied by pump or by hand
  • Easy to work with

Application areas

Choose Screed for

  • Thin-layer bonded screeds
  • Self-supporting/decoupled screeds
  • Floating screeds
  • Heated screeds

Discover more

Other solutions you might be interested in

Details

Screed is a premixed cementitious mortar, based on hydraulic binders, additives and selected aggregates, with a medium-fast setting time, to be applied when it has the consistency of damp earth, and classified as CT C20 F5 in accordance with EN 13813. It can be used for both new builds and refurbishment projects to create screeds for the preparation, levelling and/or creation of slopes in flooring prior to the laying of ceramic tiles and/or marble, natural and artificial stone, timber and parquet, PVC, linoleum, resin flooring, waterproofing systems, etc.

Instructions for use

Preparation for installation
The substrate must be dry and free from dust and dirt. In the case of bonded screeds with a reduced thickness (from 20 mm), an anchoring slurry should be applied to improve the screed’s adhesion. This should be prepared to a fluid consistency using a mixture of water, Neoplast Latex and cement in the proportions of 2 parts water, 1 part Neoplast Latex and 2 parts cement, and applied in a continuous, uniform layer (approximately 2–3 mm) using a flat brush, broom or trowel. To ensure perfect adhesion, the Screed must be laid onto the mortar whilst it is still fresh (fresh-on-fresh), or, for flooring subject to high mechanical stress, use a bonding layer made with a two-component epoxy adhesive for jointing, Epox Ripresa, diluted 1:1 with water. The bonding layer made with Epox
Ripresa, applied continuously to cover the entire surface, ensures an effective vapour barrier. For self-supporting screeds, lay a decoupling layer such as a polyethylene sheet prior to installation; in the case of rising damp, this application must include suitable waterproof membranes or liners capable of forming an adequate vapour barrier. These membranes must have a nominal Sd value of 1,500 m or greater. In perimeter areas and where vertical elements are present in the centre of the floor, ensure that a perimeter decoupling strip approximately
1 cm thick is installed.

Product preparation
Mix Screed with the appropriate amount of water, approx. 8 per cent (equivalent to 2.0 litres per 25 kg bag), using a machine (with a suitable mixing pump), a concrete mixer, a planetary mixer and/or, for small quantities, by hand.

Installation instructions
Prepare the levelling strips to the desired height, then spread the mix and compact it thoroughly, trowelling it to achieve the best surface finish. In the case of thin screeds and/or in areas where the screed overlaps pipes, cabling and technical systems, a galvanised steel mesh must be incorporated. In addition to perimeter joints, expansion joints must be provided to create modules, each normally not exceeding 20 m².

Cleaning
The equipment used for laying may be cleaned with water before the product hardens; thereafter, only mechanical cleaning will be possible.

Storage

Screed should be stored in a dry, sheltered place. It will keep for at least 3 months in its unopened original packaging.

Warnings

Do not use the product in the following circumstances:

  • At temperatures below +6 °C or above +30 °C
  • With quantities of water lower than those specified, as this will compromise the workability of the material and the quality of the laid surface, or higher, to avoid shrinkage, cracking, reduced strength and prolonged drying times
  • Do not add any other binders, aggregates and/or additives to the Screed
  • Protect the product from frost and rapid drying
  • Avoid sudden temperature changes during the setting phase

Color Code Packaging Packaging size Pallet Barcode
Grey
8431 bag 25kg
50 bags
Barcode 8030334084317

  • Thin-layer bonded screeds
  • Self-supporting/decoupled screeds
  • Floating screeds
  • Heated screeds

Parameter Value
Consistency Powder
Colour grey
Particle size 0–3 mm
Mixing water 8 %, equivalent to approx. 2.0 l per 25 kg bag
Bulk density 1600 kg/m³
Drying time Approximately 10 days at 20°C and 50% RH
Reaction to fire Euroclass A1
Coverage 16 kg/m² per cm
Category CT – C20 – F5
Minimum thickness 2 cm bonded – 4 cm floating
Application temperature +6°C / +30°C
Storage (information in accordance with the Ministerial Decree of 10 May 2004) 3 months in a cool, dry place with the packaging intact

The approximate consumption is around 16 kg/m² per cm of thickness.

Technical datasheet
Safety data sheet

Still missing information?

Contact our team for personalized support and product guidance.