T 250

Single-component cementitious powder adhesive, type C2 TE in accordance with EN 12004, flexible, non-slip and with an extended open time, for bonding all types of small to medium-sized ceramic tiles indoors and outdoors, on walls and floors.

Single-component cementitious powder adhesive, type C2 TE in accordance with EN 12004, flexible, non-slip and with an extended open time, for bonding all types of small to medium-sized ceramic tiles indoors and outdoors, on walls and floors.

  • Extended open time
  • High tack
  • Non-slip

Variations

Choose the perfect solution for your project

 
White
 
Grey

Application areas

Choose T 250 for

  • Suitable for medium-sized porcelain or glazed stoneware
  • For bonding ceramic tiles indoors and outdoors, on walls and floors
  • Bonding of ceramic tiles to substrates with limited movement and dimensions
  • Also suitable for overlay applications.

Discover more

Other solutions you might be interested in

Details

T 250 is a powdered cementitious adhesive available in white and grey, formulated with high-strength cements, selected aggregates, synthetic resins and specific additives. Once mixed with water, it produces an adhesive with excellent workability, superb thixotropy, moderate flexibility and high adhesion to all types of cementitious substrates. When applied vertically, it does not run and prevents tiles from slipping. Its extended open time allows for safe installation even in hot and draughty conditions. It is resistant to freeze-thaw cycles. T 250 is classified as a Class C2 TE cementitious adhesive in accordance with EN 12004.

Instructions for use

Preparation for installation
Substrates must be sufficiently dry, strong, sound and even, clean and in good condition, free from oil and grease, dust, loose material and general dirt, and free from any paint film residues; they must also be adequately cured and free from significant shrinkage. As a general guide, traditional cement screeds with normal setting and hardening times must have
a curing period of at least 28 days; cement plasters or plasters based on mixed mortar must be allowed to dry for at least 14 days. Major surface imperfections and irregularities, such as unevenness, cavities, gravel pockets, eroded or deteriorated areas, must be repaired in advance and levelled using self-levelling compounds, such as LIVELLINA 0-10, or with a suitable mortar, such as MULTIMIX EVO, RESTAURO, RINNOVA or MONORASANTE. Particularly porous and crumbling substrates, as well as those with very low mechanical strength and which are easily scratched, must be treated beforehand with TILE PRIMER.

Product preparation
Mix T 250 with 26–28% clean water (equivalent to 6.5–7.0 litres per 25 kg bag) until a homogeneous, lump-free mixture is obtained. Leave to rest for 5 minutes, then stir briefly. The prepared mix remains workable in the mixing container for approximately 5 hours under normal conditions (at 20 °C); higher temperatures shorten the workability time, whilst lower temperatures extend it. In the event of direct sunlight, and consequently high substrate temperatures, it is advisable to dampen the substrate with a sponge to cool it down, taking care not to leave any surface water.

Installation instructions
Apply T 250 using a suitable notched trowel, the size of the notches depending on the type and size of the tiles to be laid, so as to ensure complete
coverage of the back of the tiles. For better adhesion, it is recommended to first spread a thin, even layer of adhesive onto the substrate using the smooth side of the notched trowel, and then immediately apply a second layer of the desired thickness using the notched side. Apply the tiles by exerting adequate pressure and moving them slightly from side to side. When bonding tiles larger than 33×33 cm, with a pronounced profiled underside, for external applications – particularly in areas subject to significant temperature fluctuations or freeze-thaw cycles and considerable water stress – it is necessary to use the ‘buttering-floating’ technique: the mixed adhesive
is spread onto the substrate using a notched trowel and then applied to the back of the tile with a trowel, levelling it flush with the raised areas. The tiles must be laid only within the time window during which the applied adhesive is still fresh and tacky, i.e. before it has formed a surface skin. This time window is known as the adhesive’s ‘open time’, and depends on environmental conditions. If the open time has elapsed and the applied adhesive has formed a surface skin, it is necessary to go over it again with a notched trowel to break the skin and ‘refresh’ it. Under no circumstances should you wet the surface, as this would form a water film that prevents adhesion, thereby preventing the tiles from making contact with the adhesive and irreparably compromising the installation.
Tiles should not normally be wetted before laying; only in the case of tiles with a dusty underside is it advisable to wash them by immersing them in clean water for a few seconds. Tiles should not normally be wetted before laying; only in the case of tiles with a dusty underside is it advisable to wash them by immersing them in clean water for a few seconds. For plaster substrates, pre-treatment with TILE PRIMER or MULTIGRIP is absolutely essential.

Cleaning
The tools used for installation can be cleaned with water before the adhesive sets; afterwards, cleaning can only be carried out by mechanical removal. Any dirt on the surface of the tiles must also be wiped off with a damp cloth before the adhesive sets.

Storage

T 250 must be stored in a dry, sheltered place. It will keep for at least 12 months in its original, unopened bags. KEEP AWAY FROM MOISTURE.

Warnings

Do not apply T 250 to: wood and wood-based composites, metal surfaces, rubber, PVC, linoleum and similar materials; or to substrates subject to continuous deformation, significant movement and heavy
mechanical stress. For applications over existing coatings and/or on low-absorbent substrates where adhesion is difficult, pre-treat the surface with MULTIGRIP. For applications on plaster or anhydrite surfaces, the surface must be pre-treated with TILE PRIMER. If in doubt regarding this type of application, please consult our Technical Department. Never mix T 250 with other binders such as cement, hydraulic lime, gypsum, etc. Never add further water once the mixture has set. Do not use the mixed product once it has started to set; therefore, ensure that you prepare only the amount of mixture required for immediate application within its workability time.

Color Code Packaging Packaging size Pallet Barcode
White
5445 bag 25kg
50 bags
Barcode 8030334054457
Grey
5447 bag 25kg
50 bags
Barcode 8030334054471

  • Suitable for medium-sized porcelain or glazed stoneware
  • For bonding ceramic tiles indoors and outdoors, on walls and floors
  • Bonding of ceramic tiles to substrates with limited movement and dimensions
  • Also suitable for overlay applications.

T 250 can be used on underfloor heating systems, on plasterboard and gypsum-based renders (with primer).

TESTS ON POWDERED PRODUCTS WHITE GREY
Texture powder powder
Bulk density 1.3 kg/l 1.3 kg/l
Particle size 0–0.5 mm 0–0.5 mm
TESTS ON FRESH MIX
% water content 26–28 % (6.5–7.0 litres per 25 kg bag) 26–28 % (6.5–7.0 litres per 25 kg bag)
Bulk density of the mix 1.55 kg/l 1.55 kg/l
Consistency of the mixture paste-like – spreadable paste-like – spreadable
Slump (EN 1308) < 0.05 mm < 0.05 mm
Pot life of the mixture (at +23°C) approx. 5 hours approx. 5 hours
Open time (EN 1346) > 30 minutes > 30 minutes
Setting time (DIN 18156 Part 2) 20 minutes 20 minutes
Application temperature from +5 °C to +35 °C from +5 °C to +35 °C
TESTS ON CURED PRODUCT
Tensile adhesion (EN 1338): initial adhesion >1.2 N/mm² >1.4 N/mm²
Tensile adhesion (EN 1338): adhesion after immersion in water >1.0 N/mm² >1.0 N/mm²
Tensile adhesion (EN 1338): adhesion after heat treatment >1.1 N/mm² >1.1 N/mm²
Tensile adhesion (EN 1338): adhesion after freeze-thaw cycles >1.1 N/mm² >1.1 N/mm²
Joint filling: on wall after approx. 8 hours after approx. 8 hours
Joint filling: on the floor after approx. 24 hours after approx. 24 hours
Walkable after 24 hours after 24 hours
Full cure after 14 days after 14 days
Operating temperature from -30 °C to +90 °C from -30 °C to +90 °C
Consumption 3 to 8 kg/m²
3 to 8 kg/m²
Maximum achievable thicknesses 10 mm 10 mm
Classification according to EN 12004 C2 TE C2 TE

The consumption of T 250 can vary from 3 to 8 kg/m² depending on the type of tile and the flatness of the substrate.

Technical datasheet
Safety data sheet White
Safety data sheet Grey
Emicode

Still missing information?

Contact our team for personalized support and product guidance.