Tile 250

Improved, single-component, low-slump, powder-based cementitious adhesive with extended open time, made flexible, class C2 TE in accordance with EN 12004. Suitable for bonding medium-sized porcelain and glazed tiles indoors and outdoors, on walls and floors. Frost-resistant.

Improved, single-component, low-slump, powder-based cementitious adhesive with extended open time, made flexible, class C2 TE in accordance with EN 12004. Suitable for bonding medium-sized porcelain and glazed tiles indoors and outdoors, on walls and floors. Frost-resistant.

  • Extended open time
  • High tack
  • Non-slip
  • Even when layered

Variations

Choose the perfect solution for your project

 
White
 
Grey

Application areas

Choose Tile 250 for

  • Suitable for medium-sized porcelain stoneware or glazed tiles.
  • For bonding ceramic tiles indoors and outdoors, on walls and floors.
  • For bonding ceramic tiles to substrates with limited movement and dimensions.

Application areas

Where Tile 250 performs best

Discover more

Other solutions you might be interested in

Details

Tile 250 is a powdered cementitious adhesive available in white and grey, formulated with high-strength cements, selected aggregates, synthetic resins and specific additives. Once mixed with water, it produces an adhesive with excellent workability, superb thixotropy, moderate flexibility and high adhesion to all types of cementitious substrates. When applied vertically, it does not run and prevents tiles from slipping. Its extended open time allows for safe installation even in hot and draughty conditions. It is resistant to freeze-thaw cycles. Tile 250 is classified as a Class C2 TE cementitious adhesive in accordance with EN 12004. The product is certified as EC 1 Plus by the GEV body for its very low emissions of volatile organic compounds.

Instructions for use

Preparation for installation
Substrates must be sufficiently dry, strong, sound and even, clean and in good condition, free from oil and grease, dust, loose material and general dirt, and free from any paint film residues; they must also be adequately cured and free from significant shrinkage. As a general guide, traditional cement screeds with normal setting and hardening times must have been left to cure for at least 28 days; cement plasters or plasters based on mixed mortar must be left to dry for at least 14 days. Major surface imperfections and irregularities, such as unevenness, cavities, gravel pockets, eroded or deteriorated areas, must be repaired in advance and levelled using self-levelling compounds, such as Livellina 0-10 or Livellina 5-30, or with a suitable mortar, such as Multimix Evo, Restauro, Rinnova or Monorasante. Particularly porous and crumbling substrates, as well as those with very low mechanical strength and which are easily scratched, must be treated beforehand with Tile Primer.

Product preparation
Mix grey or white Tile 250 with approx. 28% clean water (equivalent to 7.00 litres per 25 kg bag) as follows: pour almost all of the required mixing water into a suitable container, then slowly add the powdered product, simultaneously mixing the resulting mixture using a low-speed drill fitted with a suitable mixing paddle. Once all the powder has been added, pour in the remaining water and mix until the mixture is smooth and free of lumps, taking particular care to remove any lumps of unmixed material from the sides and bottom of the mixing vessel. Leave to rest for about 5 minutes, then stir briefly. The adhesive prepared in this way remains workable in the mixing container for about 5 hours under normal conditions (at +20 °C); higher temperatures shorten the workability time, whilst lower temperatures extend it. In the event of direct sunlight, and consequently high substrate temperatures, it is advisable to dampen the substrate with a sponge to cool it down, without leaving any surface water.

Installation instructions
Apply the adhesive using a suitable notched trowel, the size of the notches on which will depend on the type and size of the tiles to be laid, so as to ensure complete coverage of the back of the tiles. For better adhesion, it is advisable to first spread a thin, even layer of adhesive onto the substrate using the smooth side of the notched trowel, and then immediately apply a second layer of the desired thickness using the notched side. Apply the tiles by exerting adequate pressure and applying a slight translational movement to them.
When bonding tiles with a longest side >30 cm and a distinctly profiled underside, particularly for external applications in areas subject to significant temperature fluctuations or freeze-thaw cycles, it is essential to use the ‘compact-layer laying’ technique”: the mixed adhesive is spread onto the substrate using a notched trowel and then applied to the back of the tile with a trowel, levelling it flush with the raised areas. Provided that a sufficient quantity of adhesive has been applied, this ensures that the adhesive-to-tile contact extends across the entire bonding surface (an essential condition for the installation of floor and wall coverings exposed to freeze-thaw cycles and significant water stress).
The tiles must be laid only within the time window during which the applied adhesive is still fresh and tacky, i.e. before it has formed a surface skin. This time window is known as the adhesive’s ‘open time’ and depends on environmental conditions. The open time of Tile 250 is greater than 30 minutes at +23 °C and 50% relative humidity. High temperatures, direct sunlight and strong draughts, as well as a highly porous and absorbent substrate, can significantly reduce the open time, whilst low temperatures, high ambient humidity and non-absorbent substrates are favourable conditions for achieving a longer open time. If the open time has elapsed and the applied adhesive has formed a skin on the surface, it is necessary to go over it again with a notched trowel to break the skin and ‘refresh’ it. Under no circumstances should you wet the surface, as this would form a non-adhesive film of water that prevents the tiles from bonding to the adhesive, irreparably compromising the installation. Tiles should not normally be wetted before laying; only in the case of tiles with a dusty underside is it advisable to wash them by immersing them in clean water for a few seconds. For plaster substrates, pre-treatment with Tile Primer is absolutely essential.

Cleaning
Tools used for installation can be cleaned with water before the adhesive sets; thereafter, cleaning can only be carried out by mechanical removal. Any dirt on the surface of the tiles must also be wiped off with a damp cloth before the adhesive sets.

Storage

Tile 250 must be stored in a dry, sheltered place. It will keep for at least 12 months in its original, unopened bags. DO NOT EXPOSE TO MOISTURE.

Warnings

  • Do not apply Tile 250 to wood and wood-based composites, metal surfaces, rubber, PVC, linoleum and similar materials.
  • Do not apply to substrates subject to continuous deformation, significant movement or high mechanical stress.
  • Never mix with other binders such as cement, hydraulic lime, gypsum, etc.
  • Never add further water once the mix has set.
  • Do not use the mixed product once it has started to set; therefore, take care to prepare only the amount of mix required for immediate application within its workability time.
  • Do not apply the product at temperatures below +5 °C or above +35 °C.
  • For applications over existing coatings and/or on low-absorbent substrates where adhesion is difficult, pre-treat the surface with Multigrip.
  • For applications on gypsum or anhydrite surfaces, the surface must be pre-treated with Tile Primer. If in doubt regarding this type of application, please consult our Technical Department.

Color Code Packaging Packaging size Pallet Barcode
White
5304 bag 25kg
50 bags
Barcode 8030334053047
Grey
5305 bag 25kg
50 bags
Barcode 8030334053054

  • Suitable for medium-sized porcelain stoneware or glazed tiles.
  • For bonding ceramic tiles indoors and outdoors, on walls and floors.
  • For bonding ceramic tiles to substrates with limited movement and dimensions.

TESTS ON POWDERED PRODUCTS WHITE GREY
Texture Powder Powder
Bulk density 1.30 kg/litre 1.30 kg/litre
Particle size 0–0.5 mm 0–0.5 mm
TESTS ON FRESH MIX
Mixing water approx. 29% (7.25 litres per 25 kg bag) approx. 29% (7.25 litres per 25 kg bag)
Density of the mix 1.55 kg/litre 1.55 kg/litre
Consistency of the mixture paste-like – spreadable paste-like – spreadable
Slump (according to EN 1308) <0.5 mm <0.5 mm
Working time of the mixture (at +20 °C) Approx. 5 hours Approx. 5 hours
Open time (according to EN 1346) >30 minutes >30 minutes
Setting time (as per DIN 18156 Part 2) Approx. 20 minutes Approx. 20 minutes
Application temperature: from +5 °C to +35 °C from +5 °C to +35 °C
TESTS ON CURED PRODUCT
Tensile adhesion (in accordance with EN 1348) initial adhesion >1.2 N/mm² >1.4 N/mm²
Tensile adhesion (in accordance with EN 1348) – adhesion after immersion in water >1.0 N/mm² >1.0 N/mm²
Tensile adhesion (as per EN 1348) – adhesion after heat treatment >1.1 N/mm² >1.1 N/mm²
Tensile adhesion (in accordance with EN 1348) – adhesion after freeze-thaw cycles >1.1 N/mm² >1.1 N/mm²
Filling of wall joints after approximately 8 hours after approx. 8 hours
Filling floor joints after approximately 24 hours after approximately 24 hours
Walkable after 24 hours after 24 hours
Full cure after 14 days after 14 days
Operating temperature from -30 °C to +90 °C from -30 °C to +90 °C
Consumption 2.0 to 5.0 kg/m² 2.0 to 5.0 kg/m²
Maximum achievable thicknesses 10 mm 10 mm
Classification according to EN 12004 C2 TE C2 TE
Storage 12 months in a dry, sheltered place 12 months in a dry, sheltered place

Coverage can vary between 2 and 5 kg/m². This depends on the type of tiles, the characteristics of the substrate and the laying method. As a rough guide, if the substrate has been properly prepared and levelled, consumption for small-format tiles is approximately 2 kg/m², for tiles up to 30×30 cm it is approximately 3 kg/m², whilst for tiles up to 40×40 cm, with pronounced profiling, and for outdoor applications (using the ‘buttering-floating’ technique), consumption is approximately 5 kg/m².

Technical datasheet
Specification clause
Emicode
Safety data sheet Grey
Dichiarazione di prestazione (grigio)
Safety data sheet White

Still missing information?

Contact our team for personalized support and product guidance.